Muratec MFX-1200 Especificaciones Pagina 116
- Pagina / 205
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4-10
4.12.3 Printout too light
Symptom: Printed image is faint or does not print solid.
Poor development
•
Remove the toner cartridge and shake it a few times to redistribute the toner
inside. If the problem persists, replace the toner cartridge.
•
Replace the High Voltage Unit.
•
Clean the LED print head.
Defective Drum
•
Replace the Drum Cartridge.
Poor image transfer
•
Replace the Image Transfer Unit.
•
Replace the High Voltage Unit.
•
Replace the Main Control PCB.
4.12.4 Printout too dark
Symptom: Printed image is faint or does not print solid.
Poor development
•
Remove the toner cartridge and shake it a few times to redistribute the toner
inside. If the problem persists, replace the toner cartridge.
•
Replace the High Voltage Unit.
•
Clean the LED print head.
Defective Drum
•
Replace the Drum Cartridge.
Poor image transfer
•
Replace the Image Transfer Unit.
•
Replace the High Voltage Unit.
•
Replace the Main Control PCB.
4.12.5 Blurred background
Symptom: Copies show a gray or dark background.
Poor development
•
Replace the High Voltage Unit.
•
Replace the Main Control PCB.
•
Replace the Toner Cartridge.
•
Replace the Drum Cartridge.
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
ABCDE
- MFX-1200 1
- Safety Information 2
- Table of Contents 4
- Section 1 9
- General Description 9
- 1.2 Specifications 10
- Section2 12
- Machine Composition 12
- PANEL PCB 16
- Battery PCB 16
- CONNECTOR (SCANNER) PCB 16
- MAIN CONTROL PCB 16
- GENERATOR 17
- 2.4 Power Supply Unit (PSU) 18
- 2.5 Sensors 19
- 2.5.2 Sensor Descriptions 20
- 2.6.1 Document Detection 21
- 2.6.2 Document Separation 21
- 2.6.3 Document Transport 21
- 2.6.4 Document Scanning 21
- 2.6.5 Document Discharge 22
- 2.7 Recording Section 23
- 2.8 Image Processing 23
- 2.8.1 Drum Charge 24
- 2.8.2 Drum Exposure 24
- 2.8.3 Development 24
- Hight voltage unit + output 25
- Eraser brush 25
- 2.8.6 Fusing 26
- Section3 28
- Adjustment Procedures 28
- Machine Parameter A:0 31
- Machine Parameter A:1 31
- Machine Parameter A:2 32
- Machine Parameter A:3 33
- Machine Parameter A:4 33
- Machine Parameter A:7 34
- Machine Parameter B:0 34
- Machine Parameter B:1 35
- Machine Parameter B:2 35
- Machine Parameter B:3 36
- Machine Parameter B:4 36
- : 37
- Machine Parameter B:7 38
- Machine Parameter B:8 38
- Machine Parameter D:0 39
- Machine Parameter D:1 39
- Machine Parameter D:2 39
- Machine Parameter D:3 39
- Machine Parameter D:4 40
- Machine Parameter D:5 40
- Machine Parameter D:6 40
- Machine Parameter D:7 40
- Machine Parameter D:8 41
- Machine Parameter D:9 41
- Machine Parameter F:0 41
- Machine Parameter F:1 42
- Machine Parameter F:2 42
- Machine Parameter F:3 43
- Machine Parameter F:4 43
- Machine Parameter J:0 43
- Machine Parameter J:1 44
- Machine Parameter J:2 44
- Machine Parameter J:3 45
- Machine Parameter J:4 45
- 3.3 Memory Switch Adjustment 46
- Memory Switch A:0 - Dialer 47
- Memory Switch A:1 - Dialer 47
- Memory Switch A:5 - Dialer 48
- Memory Switch C:0 - Reception 53
- Memory Switch C:1 - Reception 53
- Memory Switch D:0 - Reception 54
- Memory Switch D:1 - Reception 54
- Memory Switch D:2 - Reception 55
- Memory Switch D:3 - Reception 55
- Memory Switch E:0 - Scanner 56
- Memory Switch H:0 - Operation 62
- Memory Switch H:1 - Operation 62
- Memory Switch H:2 - Operation 63
- 3.5 All RAM Clear 64
- 3.7 Unique Switch Adjustment 68
- Unique Switch a:0 — Dialer 69
- Unique Switch c:0 - Reception 71
- Unique Switch c:1 - Reception 72
- Unique Switch c:2 - Reception 73
- Unique Switch c:3 - Reception 73
- Unique Switch d:0 - Modem 74
- Unique Switch d:1 - Modem 74
- Unique Switch d:2 - Modem 75
- Unique Switch d:6 - Modem 75
- Unique Switch d:7 - Modem 76
- Unique Switch e:2 - Scanner 76
- Unique Switch e:7 - Scanner 77
- Unique Switch e:8 - Scanner 78
- Unique Switch e:9 - Scanner 79
- Unique Switch f:0 - Printer 80
- Unique Switch f:1 - Printer 80
- Unique Switch f:2 - Printer 81
- Unique Switch f:3 81
- f:4 --- Factory use only 81
- Unique Switch f:5 - Printer 81
- Unique Switch f:6 - Printer 82
- Unique Switch f:7- Printer 82
- Unique Switch h:0 - Operation 84
- Unique Switch h:1 - Operation 84
- Unique Switch h:3 - Operation 85
- Unique Switch h:4 - Operation 85
- Unique Switch i:8 86
- j:3 --- Factory use only 86
- Unique Switch j:6 87
- j:9 --- Factory use only 87
- 3.8 Printer maintenance mode 88
- 3.9 Print Service Report 89
- 3.10 Print Program Mode List 89
- 3.11 Test Modes 89
- 3.11.1 Life Monitor 90
- 3.11.2 Printer Test 91
- 3.11.3 Feeder test 92
- 3.11.4 Background Level Test 92
- 3.11.5 Set Background Level 92
- Unique Switch Settings 93
- 3.13 Factory Functions 93
- 3.13.3 LCD Test 94
- 3.13.4 Key Panel Test 94
- 3.13.5 SRAM Check 95
- 3.13.6 DRAM Check 95
- 3.13.8 RS-232C Test 96
- 3.14 Line Tests 97
- 3.14.2 Tonal Signal Test 98
- 3.14.3 DTMF Output Test 100
- 3.16 Consumable order sheet 101
- Reset Order Sheet 103
- 103
- / /Enter 103
- Check Enter/Cancel 103
- 3.21 Life monitor maintenance 104
- 3.20 Set Service Code 104
- 3.22 JP1, JP2 Battery Backup 105
- 3.23 Update the software 106
- The unit should be installed: 107
- Check the consumable: 107
- 4.2 Recording Paper Jam 108
- 4.3 Document Feeder Jam 108
- 4.5 Mirror Carriage Error 109
- 4.6 Transmit Error 109
- 4.7 Transmit Black Lines 109
- 4.8 Cannot transmit 110
- 4.9 Receive Errors 110
- 4.10 Will not Auto-Answer 110
- 4.11 Clearing Jammed Paper 111
- To remove the document: 112
- 4.12.1 Blank pages 115
- 4.12.2 Black pages 115
- 4.12.3 Printout too light 116
- 4.12.4 Printout too dark 116
- 4.12.5 Blurred background 116
- 4.12.6 Uneven print density 117
- 4.12.7 Irregularities 117
- 4.12.8 White (Black) Line 118
- 4.12.9 Toner Smudges 118
- 4.13 LCD Error Messages 119
- 4.14 Error Codes 124
- Transmission errors 125
- Communication Error Messages 126
- 4.15 Service Call Error 127
- Heater Error 128
- Thermistor Disconnect 128
- Thermistor Short 128
- Inside Fan Error 128
- RX Motor Error 129
- Drum Fuse Error 129
- H-Vlt Fuse Disconnect 129
- 4.16 LCD Failure 130
- 4.17 General Power Failure 130
- 4.18 Cleaning the Unit 131
- Cleaning the LED print head 132
- Section5 133
- Maintenance & Adjustment 133
- 5.1 Maintenance schedule 134
- 5.2 Re/Disassemble 135
- 5.2.1 Covers 137
- FRONT COVER 138
- REAR COVER 138
- TOP REAR COVER 139
- HARNESS HOLDER 139
- Tx cover 140
- Tx side cover F 140
- Tx side cover R 141
- Exit tray 141
- Option cover A 142
- Rx exit cover 142
- Rx exit cover A 142
- Rx exit cover B 142
- Cover opener 143
- Cover lever 143
- PANEL COVER 144
- PLATEN COVER 144
- BOTTOM CORNER COVER 144
- BYPASS TRAY 144
- 5.2.2 PCBs 145
- Shield plate 146
- Modular PCB 146
- Fan motor 147
- Power supply unit 147
- High voltage power supply 148
- PCB shield 148
- Printer connect PCB 148
- Panel cover 149
- Film harness of the LCD 149
- LCD support 150
- LCD spacer 150
- Bottom corner cover 150
- Hinge screw 150
- Harness holder 151
- Platen cover assembly 151
- Top rear cover 151
- Screw cover 151
- Connect scanner PCB 152
- Lens cover 153
- Inverter PCB 153
- CONNECT ADF PCB 154
- Connect ADF PCB 154
- Ground wire 154
- 5.2.3 Sensors 155
- 5.2.4 Scanning section 156
- TXIL(ADF) 157
- Retard cover 158
- Retard roller assembly 158
- Torque limiter 158
- Motor bracket 159
- Spring C 159
- Pulley 50/17 G26 159
- APS bracket 160
- APS feeler 160
- Platen sheet 162
- Platen stay B 163
- Exit roller 163
- HOME SENSOR / END SENSOR 164
- FBS MOTOR 164
- Rear angle 165
- FBS motor brackect 165
- FBS Motor 165
- Belt retainer 166
- Flat cable 166
- 1. Open the TOP COVER 167
- 2. Remove the SPRING 167
- 4. Pull out the KNOB 167
- Cover switch 168
- Solenoid 169
- Rx motor 169
- Drive gear assembly 170
- Pick up roller MP 171
- Image transfer roller 172
- Fxing unit cover 173
- Themistor 173
- Exit roller P 173
- Plate spring 173
- Paper pick up roller 174
- Feed roller BP 175
- MP bracket 175
- Main frame 176
- Press spring B 177
- Release lever 177
- Press roller BP 177
- PSS cover 177
- LED print head 178
- Bypass tray 179
- 5.3 Adjustment 180
- Section 6 181
- Packaging contents: 183
- Installation 183
- PHONE1PHONE2 183
- 6.3 RS-232C interface 184
- 6.3 Page Counter 187
- 6.4 AL-200 188
- 6.5 OP-100/NP-200 192
- Installing the Printer driver 196
- 6.6 Attaching the 2-Bin tray 197
- RX exit cover A 198
- OPTION COVER A 200
- EXIT TRAY 200
- RX EXIT COVER 201
- 6.7 Second paper cassette 202
- 3x10mm screws 204
- Setting of the Paper Size 205
Relacionado con productos y manuales para Multifuncionales Muratec MFX-1200
Multifuncionales Muratec F-32 Manual de usuario
(6 paginas)
(6 paginas)
Multifuncionales Muratec F-360 Manual de usuario
(16 paginas)
(16 paginas)
Multifuncionales Muratec F-360 Especificaciones
(290 paginas)
(290 paginas)
Multifuncionales Muratec MFX-2590 Especificaciones
(279 paginas)
(279 paginas)
Multifuncionales Muratec MFX-1450D Manual de usuario
(23 paginas)
(23 paginas)
Multifuncionales Muratec F-560 Manual de usuario
(23 paginas)
(23 paginas)
Multifuncionales Muratec MFX-3070 Manual de usuario
(193 paginas)
(193 paginas)
Multifuncionales Muratec MFX-1820 Manual de usuario
(93 paginas)
(93 paginas)
Multifuncionales Muratec F-560 Manual de usuario
(2 paginas)
(2 paginas)
(42 paginas)
(54 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales